Greenwich Instrument Co. Inc
X-Ray High Voltage Cables
For Test or X-Ray system installation: We can meet virtually any x-ray cable need at hard to beat prices. We can get you any standard or obscure termination you may need!
Standard X-Ray Cable Pricing
*Note: all prices are in US dollars.
Standard high voltage cable M series 3/c 100 KV Flex, 0.785" (19.39 mm) diameter with straight or angled split strain relief. Skirted cable nuts standard, spanner nuts optional.
Type L low noise hi-flex, 3/c 75 KV 0.650" dia:: Cable are usually available in 5 foot increments.
Also available Type M Low Noise , 0.785" diameter 3/C . This is 100 kV cables with Federal Standard 75 KV termination.
Special assemblies and terminations for specific CT scanners, mobiles, etc. 4 conductor cables for grid pulse available.
Also R-24 extra high voltage, and extended federal standard for 150 KV+
Let us quote your needs. Drop shipped FedEx Saver from manufacturers stock, direct to your location. F.O.B. Connecticut. VISA, MC, AMEX. Net 30 to current accounts.
Test Cable Descriptions
Instruction books for the Dynalyzer recommend using cables of 5 foot (1.5m). Longer cables will introduce extra capacitance and resistance into the circuit.
*Note: all prices are in US dollars.
-
HV3-5G X-Ray Test Cable
$240each, $450 per pair
The type "G" spanner nut for this cable is similar to the standard nut on GE(tm) HV cables. Our cable nuts are slightly taller than the standard GE nut, so there is extra finger grip room. Spanner holes are located in the top of the nut. We recommend these cables if you are using a GE bleeder. A tube of insulating compound included with each cable. Spanner wrenches are $100 each. Our nut is slightly taller than standard GE nut so there is more knurled area for a good finger grip. -
Lorad Test Cable
$395
Part LR-1 is a 5 foot test cable for use with Lorad Mammography machines. Plug the Federal Standard end of the cable into the voltage divider Anode, and the long (red) end into the generator test socket. You may want to put a dummy plug into the open end of the voltage divider for safety. -
Alden style test cable set
Fed Std. to Alden Male 5ft. ALM-5 $395
Coaxial Male Fed. Std. to Femaile ALF $300
Adapter ALMF-1 (set) $600
These cables are used in the Bennett mammography x-ray generators. There are two parts in the set. Part AL-M1 is a cable with Federal Standard 3 pin connector on one end of a 3 foot HV cable, and an Plug the AL-F1 into the Dynalyzer or Voltage divider Anode Transformer end, remove the cable from the tube and plug into the adapter. Plug the AL-M1 into the other anode receptacle, and reconnect the Alden plug back to the tube. Be sure of ground continuity.
-
Dynalyzer Digital Display Cable: Used to connect the Digital Display to the high voltage unit. All new components. $395.00
-
Taper Plug Test Cable
Call for price and details.
The taper plug cable is used in modern, compact x-ray equipment.
-
High Voltage Extension Cable
Call for Price and details.
This unique component has many uses. One can pre-wire an x-ray table with this part. Snake the cable from one end of the table to the x-ray tube. On installation, one only needs connect the generator to the female termination of this set. The HV extension cable is also used with the Inspec 200 system to facilitate its easy use, and operation in under table situations, and allows the various test cables to be used with it. -
Dummy Plug
$150.00
The dummy plug is used to prevent energized HV receptacles from arcing. It should be greased with dielectric silicone grease, or oil.
It is available without pins DP3-O, or with 3 pins shorted DP3-S. Supplied with pull cord and locking hardware. Other varieties available.
